Leaking, Corroded, or Burst Pipes in Star, TX? Masters Plumbing Service Fixes It
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Star, TX use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
How Masters Plumbing Service Approaches Pipe Repair in Star
Our techs work on every pipe material found in Star, TX homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
We use thermal imaging as a complement to acoustic detection — particularly useful for slab leaks and leaks inside insulated wall cavities where sound transmission is reduced.
🛠️
All Pipe Materials & Joining Methods
Our techs are proficient in copper sweating (soldering), press-fit connections (ProPress system), CPVC solvent welding, PEX crimp and expansion fitting installation, threaded galvanized repair, and ABS/PVC drain line work. We match the repair method and material to the existing pipe system rather than forcing incompatible transitions.
🔒
Pressure-Tested Before We Leave
Drain line repairs are water-tested by running fixtures through the repaired section and visually confirming no seepage at the repair joint and downstream.
Our Pipe Repair Services
Every Pipe Repair Type We Handle in Star, TX
From a pinhole copper leak behind a kitchen cabinet to a full galvanized repiping, our pipe crew in Star, TX handles the full range.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
Cross-linked polyethylene (PEX) is the current standard for residential supply piping. Failures are uncommon but occur at crimp or clamp fittings that were improperly installed, at pipe runs exposed to UV degradation, or at locations where the pipe was kinked during installation. We repair using expansion fittings (for PEX-A) or crimp fittings with the correct ring size for the pipe diameter.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed — because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Supply line leaks under a concrete slab are identified by acoustic detection and confirmed by thermal imaging. Once located, we evaluate three repair options: direct-access repair (jackhammering to the pipe, repairing the section, and patching the slab); rerouting the line through the wall framing above slab to bypass the failed underground run; or epoxy pipe lining for older copper systems with systemic pinhole corrosion.
Full Repipe
Whole-House Repipe Service
When galvanized supply lines are at end of life or polybutylene pipe (recalled for chronic failure) is in the home, a full repipe with PEX or copper is the permanent solution. We run new supply lines through the structure, transition all fixture connections, pressure test the entire new system, and patch access points in walls and ceilings.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
We pressurize the supply system and monitor for pressure drop to confirm an active leak. Then acoustic listening devices and the thermal camera locate the failure to within a small area — telling us which section of wall, floor, or slab to open.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
You receive a written summary of what failed, what we installed, and the warranty terms before we leave.
Customer Reviews
Real Pipe Repair Reviews from Star, TX Homeowners
★★★★★
Water stain appeared on my kitchen ceiling from the bathroom above. I expected them to tear up the entire bathroom floor. Instead the tech ran a pressure test, found a 12% pressure drop over 10 minutes, then used the acoustic device and identified the leak at a failed sweat joint in the copper supply to the toilet — accessible through a 14-inch drywall cut in the ceiling below. Repair was maybe $280 including the detection. I'd been dreading a $2,000 floor demo.
— N. Bergman, Star
★★★★★
Our galvanized supply lines finally gave out — low pressure everywhere, rust-colored water at some fixtures. Masters Plumbing Service repiped the whole house with PEX over two days. They confirmed pressure and flow at every fixture before leaving, patched all the wall access points smooth, and cleaned up each work area. One year later, no issues at all.
— O. & R. Adeyemi, Star, TX
★★★★★
I noticed my water meter spinning with all fixtures off — confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
— F. Okoro, Star, TX
Common Questions
What to Know Before Calling for Pipe Repair in Star, TX
Watch your water meter with all fixtures off. If the meter dial is moving or the leak indicator light is turning, water is escaping somewhere in your supply system. Other signs: unexplained increases in your monthly water bill, soft or discolored spots on walls or ceilings, mold or mildew smell in a room without a visible source, or a running sound inside walls when all fixtures are off.
In some cases — particularly for older copper systems with multiple pinhole failures along a supply run — rerouting the line through accessible framing rather than repairing it in place is more practical and more permanent. We present both options when they're both viable.
Repair options include direct slab access (jackhammer to the pipe, repair, patch), rerouting the supply line above slab through framing, and for copper systems with multiple pinhole failures, epoxy pipe lining from inside the pipe without excavation. We use acoustic and thermal detection to locate the leak before recommending a repair approach.
Galvanized pipe corrodes from the interior outward — by the time one section fails, the rest of the pipe is in varying stages of the same process. A localized repair buys time, but another section typically fails within 1–3 years if the system is at end of life. The honest answer is: it depends on how far along the corrosion is and how many sections are already narrowed or showing surface rust.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
Our pipe repair quote includes clean access cuts and leaving the opening ready for patching — with a clean, straight cut that accepts a standard drywall patch. We can typically patch the access opening as part of the job on request, though finish painting and texture matching are typically handled by the homeowner or a drywall contractor for best cosmetic results.
Service Area
Your Local Pipe Repair Specialists in Star, TX
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Star homes and businesses.
